Скачать с ютуб Crown Vic WAP Block Swap, Boost Prep, Twin Turbo Crown Vic Budget Build в хорошем качестве

Crown Vic WAP Block Swap, Boost Prep, Twin Turbo Crown Vic Budget Build

We got our "new" engine, tear it down, file the rings and get it back together awaiting the next phase of the build. We found that the slush box transmission must have been slipping on the dyno, either that or someone swapped out the atf with bbq sauce. That explains a few things.... So I will fix that by giving it the appropriate amount of pedals and swapping in a 5 speed (T45), and will plan on updating that with a tkx when that trans decides it hates us (1 day). EP-1    • Ep-1, Twin Turbo P71 Crown Victoria, ...   EP-2    • Ep 2, Twin Turbo P71 Crown Victoria, ...   EP-3    • Ep 2, Twin Turbo P71 Crown Victoria, ...   EP-4    • Ep 4, Twin Turbo P71 Crown Victoria, ...   EP-5    • Ep 5, Twin Turbo P71 Crown Victoria, ...   EP-6    • Ep 6, Twin Turbo P71 Crown Victoria, ...   EP-7    • Ep 7, Twin Turbo P71 Crown Victoria, ...   EP-8    • Ep 8, POS Wastegates, Testing and Ben...   EP-9    • Ep 9, First Start, Blow Off Valve, Fu...   EP-10A    • Ep 10A Oil System Scavenge Pump FAIL!...   EP-10B    • Ep 10B Dyno Tuning a Twin Turbo Crown...   Full Build in 19 Min    • Twin Turbo 2010 Crown Victoria Full B...   PARTS USED SO FAR.... (Using these links helps support the channel) Turbo kit used (qty 2)---https://amzn.to/3CzrXqb Exhaust hangers---https://amzn.to/34xgoTW Mandrel Bend 2.25"---https://amzn.to/3Iac2A2 2" Turbo Ducting (between the turbos)---https://amzn.to/3CGuaR1 90* 3" elbow (will be replaced w/ 45* boot) https://amzn.to/3Je50LV T3-T4 Turbo exhaust flange (input) https://amzn.to/3JfPK17 Deatschwerks 60 lb injectors EV14---https://deatschwerks.com/products/18u... NGK TR7IX Spark plugs---https://amzn.to/3JlGg4h Coils (ACDelco)---https://amzn.to/3KUUQQU Coils (MSD that one went bad in 5k)---https://amzn.to/3Jo3KWu Rubber coated zip ties 12" ---https://amzn.to/3qng2XA Rubber coated zip ties 8" ---https://amzn.to/3Is3kNF TurboWerx Base Model Spartan High-Temperature Electric Oil Scavenge Pump ---https://amzn.to/3qpLULj Fiberglass exhaust wrap, qty 2 rolls ---https://amzn.to/3wpPeK9 POR 15 exhaust paint ---https://amzn.to/36lNFlQ 45* 3" Turbo boot ---https://amzn.to/3It1HPU mass airflow intake tube ---https://amzn.to/3D284s0 Aeromotive 340 fuel pump (almost a direct fit) ---https://amzn.to/3L1YjwR mini fuse tap --https://amzn.to/3ugHveT wastegates EMUSA, 38mm ---https://amzn.to/3K0U4S8 TurboSmart "Boost T" wastegate controler ---https://amzn.to/3qSu57W Fuel Filter -6an ---https://amzn.to/3J5anMs 5/16 to -6an adapters (x2) ---https://amzn.to/3J4G5cW -6an female to -6an female adapters (x2) ---https://amzn.to/3K58WPj 3/8 x 3/8 x 1/4 tee (I had to make one differently) ---https://amzn.to/36QJ9MA Water methane injection ---https://amzn.to/3umCrqC Oil System Fittings listed below (I used JP fittings, however these are equivalent and more available) RETURN LINES *This kit comes w/ all the fittings and 20' hose needed EXCEPT additional needed fittings listed below https://amzn.to/3JyTxqo 8an 180 (turbo's) qty 2 ---https://amzn.to/3wpSfdJ *8an to 1/4" NPT (oil pan) ---https://amzn.to/3Iv2Beq *8an to 3/8" NPT (scavenge pump) qty 2 ---https://amzn.to/3JvoPhW SUPPLY LINES *1/4 Brake hardline roll ---https://amzn.to/3JwGuFT *1/4 to 1/8 npt compression fitting (turbo side) qty 2---https://amzn.to/3D6ZEjh *1/4 to 1/4 npt compression fitting (engine side) ---https://amzn.to/3Jtakv6 WAP Block Swap Parts Side Bolts (9mm WAP Block) https://amzn.to/3FeOXw3 Oil Pan https://amzn.to/38InbvQ Gasket Set (missing oil pan, rear main, and front balancer seals) https://amzn.to/3OTVcde Timing set with oil pump and incorrect water pump https://amzn.to/37b1HY1 Oil Pan Gasket https://amzn.to/3KyBb8N High Volume Oil Pump https://amzn.to/3LGIqNc Stainless Exhaust Manifold Bolts https://amzn.to/3OUlJqF Head Bolts (2 sets req) https://amzn.to/3OTLVly Rear Main Seal with Sleeve for install https://amzn.to/38KYBue SPECIALTY TOOLS USED SO FAR.... EP 1 -Dewalt Rod Cutter (all thread technically)---https://amzn.to/3Kzx50l EP 1-5 -Exhaust cutter---https://amzn.to/3CFr0ge EP 2? -Body saw for curving insert cuts---https://amzn.to/3wap8Ld EP 5 -Tap for oil pan -https://amzn.to/3Jvjd7k EP 8 -Valve spring compressor use on wastegate -https://amzn.to/3wWufis REFERENCE VIDEOS--- Exhaust Expander How To Video---   • Exhaust Pipe Expander that Actually W...   #twinturbo #p71 #policecar #hotrodanything #blownengine #dynotuning #thrownrods