Из-за периодической блокировки нашего сайта РКН сервисами, просим воспользоваться резервным адресом:
Загрузить через ClipSave.ruУ нас вы можете посмотреть бесплатно How to Tie the Saddlemakers Latigo Knot или скачать в максимальном доступном качестве, которое было загружено на ютуб. Для скачивания выберите вариант из формы ниже:
Если кнопки скачивания не
загрузились
НАЖМИТЕ ЗДЕСЬ или обновите страницу
Если возникают проблемы со скачиванием, пожалуйста напишите в поддержку по адресу внизу
страницы.
Спасибо за использование сервиса savevideohd.ru
We all know how important it is (find this video on the Dennis Moreland Tack blog at https://www.dmtack.com/tie-saddlemake...) to check our latigo and double off for wear and deterioration each time we saddle up. If you’ve purchased a new latigo and would like to attach it to your saddle dee with a clean, nice looking and nearly flat knot this video will show you how. This knot also works for rear billets. We visited with saddle maker Mark Meek of Mark Meek Saddlery in Weatherford TX to learn how to properly tie this knot. In addition to your latigo you will need an awl, pliers and saddle soap. Follow this easy guideline while you watch the video: 1. Rub both sides of your tie string (lace) through paste saddle soap to make it easier to slide in and out of the holes of your latigo. The edges of your string should already be beveled. 2. Fold the latigo so all 6 holes line up. These holes will form a triangle. The short part of the fold (the front of the latigo and the part that will be facing you) should be facing up. 3. Thread each tail of the lace/string through one of the bottom holes of the triangle going from the front to back. 4. From the back pull the strings tight. Make sure they are even. 5. Thread both ends of the string through the top hole from back to front. Make sure there are no twists. Pull the ends tight. 6. Lace each end of the tie string back through each of the bottom holes. Pull the strings tight. The tie string ends have now been laced through each bottom hole twice. 7. Use an awl or Phillips screwdriver to open the holes on the bottom of the triangle. You’ll need enough space to put the string through once more. Be careful not to puncture the string. 8. From back to front bring one end of the lace around the side of the latigo and thread it through the bottom hole on that side. Make sure it’s not twisted. Use the pliers to pull the string about half way through. This is the third time the string has been threaded through the hole. 9. Do the same on the other side. 10. Turn the latigo over. Use the pliers to twist the looped parts of the tie string slightly, near the holes, so each side of the string is perpendicular to the edge of the latigo. Finish pulling the loop portion of the knot tight by pulling each tail with your pliers. 11. Thread each tail under the opposite side of the knot that formed the V portion of the triangle. 12. Pull the strings taut. 13. Trim the string ends and tap the knot flat with a flattening hammer. All latigos http://bit.ly/2dHjuYn at Dennis Moreland Tack are made from firm, tight-fibered burgundy latigo leather. They have been edged, hand-rubbed and waxed. They are exceptionally high quality and have great feel. There are a variety of sizes to choose from and we can custom split your latigo if you’d like. To get more information call 817-312-5305 or visit: http://bit.ly/2dHjuYn. We’re a full line manufacturer of handmade tack and we’re here to help you!