Скачать с ютуб Fixing Bosch Series 8 oven touch pad not working—Touch Calibration/博世8系列蒸烤爐/烤箱 觸控面版失效校正 в хорошем качестве

Fixing Bosch Series 8 oven touch pad not working—Touch Calibration/博世8系列蒸烤爐/烤箱 觸控面版失效校正

我的蒸烤爐型號為Bosch Series 8 oven CSG656RS7，右側的觸控面版失效。 有幸在mobile01(台灣社群網站)看到網友分享的Guru McDoc的影片Bosch Kaffee Vollautomat (CTL636EB6/05) - Touchdisplay Kalibrieren，雖然這部影片是針對Bosch的咖啡機進行校正，但將其校正方法轉化運用在蒸烤爐，也能成功修復失效的觸控面版。 Bosch Kaffee Vollautomat (CTL636EB6/05) - Touchdisplay Kalibrieren(   • Bosch Kaffee Vollautomat (CTL636EB6/0...  ) 操作模式如下： 1.啟動維修人員模式/enter to the service mode 在關機模式下，雙手同時操作，左手按「沙漏」，右手按「i 」，這時會連續聽到二聲短音，二手仍按住「沙漏」與「i」，再立即按下「on/off」，聽到一聲短音後放開雙手，即可進入維修人員模式。 操作影片如下：    • Bosch Series 8 oven enter to the serv...   2.觸控螢幕校正模式/Touch Calibration 2.1操作圓環旋鈕，找到「Touch Calibration」，再按「start」，開始進行校正。 我是仿效Guru McDoc，使用bosch的「圓環旋鈕」來操作，但我不清楚使用「圓環旋鈕」的原因為何。校正過程中，我也曾嘗試用手操作，也可以觸控本已失效的右側面版，不過，最後還是在使用「圓環旋鈕」時校正成功的。 2.2拆下「圓環旋鈕」，依照螢幕指示，依序在黃色方塊及亮紅燈的按鈕處使用「圓環旋鈕」長按。 2.3出現「Button Test」時，將「圓環旋鈕」放回，並進行以下動作： 2.3.1先向左，再向右旋轉「圓環旋鈕」 2.3.2按「on/off」 2.3.3按「start/off」 2.3.4按螢幕顯示的1、2、3、4、5、6 2.3.5按亮紅燈的按鈕 2.4當這些步驟都完成時，左下角會顯現「finished」，這代表觸控面版校正成功了。 3.錯誤排除 3.1錯誤代碼 E0537 一開始操作「Touch Calibration」的過程中，出現了錯誤代碼E0537，經反覆測試，並觀看Guru McDoc影片後，找出原因為漏按亮紅燈的按鈕。 3.2 錯誤代碼E0539 克服了錯誤代碼E0537後，又反覆在校正的最後一步驟出現錯誤代碼E0539。仔細研究Guru McDoc的影片，會發現當完成步驟2.2後，咖啡機旋鈕中間的螢幕會出現下一步的指引畫面：按向左、向右旋轉「圓環旋鈕」及按「on/off」、「start/off」，但蒸烤爐旋鈕中間的螢幕卻沒有出現相同的指引，而是出現「Button Test」，這極易使我們忽略這四個按鈕的操作，也就導致校正失敗，出現錯誤代碼E0539。 因此，校正蒸烤爐時的重要步驟，就是在出現「Button Test」時，要先向左、再向右旋轉「圓環旋鈕」，再按「on/off」及「start/off」。按按鈕的速度太慢而沒按到，也會出現E0539。重點就是在button test階段，面版上的每一個按鈕一定都要按到。 My steam oven model is Bosch Series 8 oven CSG656RS7, and the touch control panel on the right side has stopped working. Fortunately, I came across a video by Guru McDoc.Although the video is about calibrating Bosch coffee machines, the calibration method can be adapted to successfully repair the malfunctioning touch panel on the steam oven as well. Operating steps are as follows: 1. Enter the service mode: In the power-off mode, simultaneously press “hourglass” with the left hand and “i” with the right hand. You will hear two short beeps. While still holding “hourglass” and “i,” immediately press “on/off” and release both hands after hearing a short beep ,and then enter the service mode. Operation video:    • Bosch Series 8 oven enter to the serv...   2. Touch screen calibration mode: 2.1 Use the rotary knob to find “Touch Calibration,” then press “start” to begin calibration. I followed Guru McDoc’s method using Bosch’s rotary knob, though I’m unsure why the knob is used. During calibration, I attempted manual touch, and the right side panel, which was initially malfunctioning, responded. However, success was achieved using the rotary knob. 2.2 Remove the rotary knob and, following the screen prompts, long-press at the locations of the yellow square and the lit red light using the knob. 2.3 When “Button Test” appears, place the rotary knob back and perform the following actions: 2.3.1 Rotate the rotary knob left and right. 2.3.2 Press “on/off.” 2.3.3 Press “start/off.” 2.3.4 Press the buttons displayed on the screen: 1, 2, 3, 4, 5, 6. 2.3.5 Press the button with the lit red light. 2.4 When these steps are completed, “finished” will appear in the bottom left corner, indicating successful touch panel calibration. 3. Troubleshooting: 3.1 Error code E0537: Initially, during the “Touch Calibration” process, error code E0537 appeared. After repeated tests and reviewing Guru McDoc’s video, it was discovered that a button with a lit red light was missed. 3.2 Error code E0539: Overcoming E0537, error code E0539 occurred repeatedly in the final calibration step. Detailed analysis of Guru McDoc’s video revealed that after step 2.2, the coffee machine’s screen displayed the next instruction: rotate the rotary knob left and right and press “on/off” and “start/off.” However, the steam oven’s screen did not show the same guidance but displayed “Button Test.” This easily led to overlooking the operation of these four buttons, resulting in calibration failure and E0539. Therefore, a crucial step in calibrating the steam oven is, during the “Button Test” phase, to first rotate the rotary knob left and then right, followed by pressing “on/off” and “start/off.” Pressing the buttons too slowly or missing any can also lead to E0539. The key is to ensure each button on the panel is pressed during the button test phase. The translation was generated by ChatGPT.