Скачать с ютуб DIY Custom Display Case Tutorial | Posing with Peter в хорошем качестве

DIY Custom Display Case Tutorial | Posing with Peter

Hey everyone, for this video I go over a brief guide on how to build custom display cabinets at a relatively affordable cost. == TIME STAMPS == Intro & Figure Showcase: 0:00 - 1:59 Costa's Shoutout: 2:00 - 2:47 Build Tutorial: 2:48 - 6:58 Overview & Final Cost: 6:59 - 7:37 Channel Update & Outro: 7:38 - 8:41 Special thanks to Costa ‪@PopCultureLivingRoom‬ for inspiring this passion project and for allowing me to feature clips from his videos. Be sure to check out his in-depth tutorials!    • DIY Custom Display Case   == SOCIALS == Peter’s Instagram   / posingwithpeter16   Come say hi on Facebook @ Sixth Scale Posers https://www.facebook.com/groups/44272... == NON AFFILIATE LINKS TO MATERIALS == Black Steel Shelf https://www.walmart.com/ip/Juggernaut... White Hard-Board https://www.homedepot.com/p/EUCATILE-... Black Microfiber Bed Sheet https://amzn.to/3bj9Onx White Light Bars 6500K 8-pack https://amzn.to/3Q65Ayc Magnetic Tape https://amzn.to/3zhYT5t Black Duct Tape (for backings) https://amzn.to/3oI3tFj Black Vinyl Tape (for acrylic borders) https://amzn.to/3POen8k Novus Plastic Cleaner https://amzn.to/3oCHWh9 Jig-Saw Cutter https://amzn.to/3OLb9kK ** FAQ ** Hi everyone! It’s been a year since I made this video and I’ve been fortunate enough to receive such overwhelmingly positive feedback along with many follow up questions on the build process. I figured it best to address some of these frequently asked questions so you don’t have to go looking for the answer in the comments below ☺️ * What thickness are the acrylic panels? * 1/8th inch for each panel all around. It’s worth mentioning that I’ve built 2 additional cabinets and used 1/8th inch panels for the front to maintain rigidity but used 1/16th inch panels for the sides since they were a bit cheaper. Heads up they are flimsy / less rigid but they get the job done since I never remove the side panels. * How did you fit the light bars into the cabinet? * I fully inserted the connectors as much as possible into each end of the light bar then folded / bent the wire-connector 90 degrees to fit into the cabinet. It’s a tight squeeze but you can briefly see it around the 5:55 mark. Alternatively if you can buy the 3-foot light bars instead for better clearance without the need to forcefully bend any connectors. * Did you wrap both sides of the shelves in black cloth or just the top side? * I wrapped both sides of each shelf in black cloth for the sake of uniformity. It requires more material but was worth the final outcome in my opinion. * How is the magnetic tape holding up? * Some parts of the adhesive magnetic tape did indeed wear off after uploading this video possibly due to weather / climate or just cheap materials. An easy solution was buying this pack of small circular neodymium magnets. I just super-glued a few of them around the corners & edges of acrylic borders for a much stronger magnetic hold to the metal frame. Non-affiliate link: https://a.co/d/3TnxNvw * How did you join the cabinets together? * Just inserted black zip ties through the holes of the vertical metal frames where the 2 cabinets meet in the center. That’s all for now but I’ll add more to this list if it comes to mind 😅 As always thanks so much all your kindness and support. Best of luck on your custom builds, and until next time, stay safe and take care! ❤️ #hottoys #customdisplay #diy