Скачать с ютуб How to Seal & Fill Liquid Resin Shakers: NO LEAKS, FOOLPROOF в хорошем качестве

How to Seal & Fill Liquid Resin Shakers: NO LEAKS, FOOLPROOF

EDIT PLEASE READ at 11:45, I said I used 1/8 inch hole punch when I meant to say 1/16 inch. Sorry for the confusion! You can also sand the frame surface where the plastic film is going to lay on to increase overall adhesion. Normally this is not a necessary step if you’re sealing/doming on a piece that hasn’t reached its full cured state (which takes about 3 to 7 days). If your resin has way past the soft cured stage and is fully cured, then I recommend the sanding. ****Many commercial shaker resin molds have a slit or a notch for the needle for filling the shaker liquid. I hate this because I can never seal it properly using that. So I normally fill it in with resin. Check out this video on how I do it:    • Watch Me Resin: BT21 Liquid Shaker Re...  . (At 3:47 mark) I’ve learned how to seal properly through trial and error. I’ve also learned one of the techniques from other YouTuber, MoultingRook. Check out her video and use it as one of your resources:    • Total Beginner’s Guide to Epoxy Resin...   Buy me a cup of "resin" to help me support this channel: https://ko-fi.com/amymade Instagram: @amymade.Ig Tiktok: @amy_made [email protected] My Shop: https://www.emiialchemii.com IMPORTANT NOTICE: Please ALWAYS use resin with proper precautions including wearing proper PPEs (glove, mask, respirator etc) AND working in a well ventilated space. I recommend getting a hold of the SDS (Safety Data Sheet) info that every resin company has available to the public (by law). This has all the info about the resin you are using including the precautions you need to take and first aid care. Watch my resin safety video for more info:    • RESIN SAFETY | Important Info All Res...   FAQS regarding this video: Q: I DONT HAVE UV RESIN, CAN I USE 2PART RESIN TO GLUE ON THE PLASTIC FILM? A: You can but the film may slide off so you would have to baby sit the film for a while until the resin has cured enough where it won’t move. OR you can wait for the resin to get thicker and stickier before gluing the film on. Q: I don’t have uv resin, can I use clear glue to seal the plastic film onto the frame? A: as long as you have a leak free seal with the glue...I guess? But you’re going to be able to see the glue even after you seal it with resin. Supplies I used were purchased from many places including my local craft stores, Etsy, Ebay, Amazon, Sophie&Toffee, Miniature Sweets, and Aliexpress SUPPLIES USED (Affiliate links are marked with * .I get a small commission at no cost to you. Please use them as it will help me continue to make content on this channel! Thank you!) *Shaker molds:https://amzn.to/38HCnoK *Casting resin: Liquid Diamond casting resin https://www.theepoxyresinstore.com/co... (coupon code for 20% off : CRAFTERSDELIGHTS20) Doming resin: Faux Rizzle coating Resin (Noveau) https://artresinfauxrizzle.com/faux-r... UV-LED resin: https://www.emiialchemii.com/product/... Needle point squeeze bottle: www.emiialchemii.com/product/1oz-needle-point-squeeze-bottle Baby oil: local discount store Isopropyl alcohol: Drug store *1/16inch punch: https://www.amazon.com/Fiskars-Inch-H... Plastic film for shaker: By Grafix 0.007 thickness Drill: https://www.amazon.com/gp/product/B07... Why do I use two different types of resin in my projects? I use a casting resin rocast and a doming resin for doming. Casting resin is usually low in viscosity and works very well in molds without much issue with the bubbles. Also the low viscosity will allow the resin to reach detailed area of the mold. Doming resin is thick in viscosity and holds its shape very nicely. It creates a full dome and tends to hold the surface tension much better than low viscosity resin. So lower risk of the resin dripping off the sides. It also gives the piece a smooth, flawless finish. Videos for Resin Beginners: Part 1    • Everything You Need to Know About 2 P...   Part 2    • How to Measure and Mix Resin | Comple...   Part 3    • How to Dome with Resin | Complete Beg...   Disco Sting by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. https://creativecommons.org/licenses/... Source: http://incompetech.com/music/royalty-... Artist: http://incompetech.com/ Music provided by Epidemic Sound