Скачать с ютуб LS Swapping a Squarebody C10 | PECOS GETS A NEW HEART | Part 1 в хорошем качестве

LS Swapping a Squarebody C10 | PECOS GETS A NEW HEART | Part 1

In this video, we're LS swapping a squarebody c10 - @twotrucksron's squarebody C10 to be exact...yep, Pecos is getting a new heart. WE SURPRISED OUR BUDDY WITH A 1984 SQUAREBODY C10:    • WE SURPRISED OUR BUDDY WITH A 1984 SQ...   Two truck's Ron's IG:   / twotrucksron   Speed Engineering LS Swap C10 Longtube Headers (do not hang below frame rail on Pecos): https://amzn.to/31HzjFd GM Muscle Car Oil Pan(19212593): https://amzn.to/2CBosBn Corvette-style fuel regulator: WIX 33737 budget option: https://amzn.to/2X0Qm1v AC Delco OEM-spec option: https://amzn.to/2LjqADv If you haven't seen the rest of this LS Swap series, check out the playlist below:    • LS Swaps   Or if you want to pick and choose, select one from the list: Part 1:    • LS Swapping a Squarebody C10 | PECOS ...   Part 2:    • LS Swapping A Squarebody C10 | THE ST...   Part 3:    • LS Swapping a Squarebody C10 | YOU GO...   Part 4:    • LS Swapping a Squarebody C10 | FIRE. ...   @C10Squared's list and commentary on LS Swapping a Squarebody C10 (cleaned up for YouTube description format and WG's advice incorporated). WG's Amazon Affiliate Links will be provided where applicable (parts purchased via these links supports WG) Keep in mind this is for Squarebody trucks. Primary differences for other year C10s will be fuel tank setup and engine mounts. For example, Dirty Dingo mounts seem to be preferred for 67-72, however Tejas are preferred for 73-87 c10s. This is my (c10 squared) recipe and there are many ways to do this; this is just how I do it. Engine mount plates Tejas Steelworks $100 Chevy 350 engine mounts $40 Gaskets for headers above Summit NAL-92202326 $25/pr Radiator - new factory radiator $120 Lower radiator hose Napa PN 7499 $30 Upper radiator hose for a 2000-2006 suburban $40 1999 Ford Windstar fans from RockAuto $90 Tanks Inc Fuel Injection tank for 1973-1987 $225 + shipping Tanks Inc sending unit for stock gas gauge $35 Tanks inc GPA4 fuel pump kit (walbro 255lph pump) $225 (the above is for trucks, if suburban has rear mount tank, would just buy a new one of those and then install a 1987 Suburban sending unit and a walbro 255LPH pump and use 5/16 and 3/8 to 6AN compression fittings; you can also save some $ and use your factory truck tank with a 1987 sending unit/walbro combo with compression fittings) Tanks Inc LS swap fuel line kit with fittings & regulator $235 (fuel regulator info above) Engine harness: I use BP Automotive for the harnesses and use the premium service which includes fuel pump relay $550 (Ron used PSI on Facebook and WG used PSI on Teddy as well) Fan harness with relays $80 Tuning (I have BP tune the ecm or buy a tuned one from them $75 Drive shaft shortened if needed $200 o2 Sensors if needed $100 https://amzn.to/2L1kwzp (for PSI harness; check for BP) Lokar shift linkage for 4l60e $65 https://amzn.to/2Xr5WaW Lokar transmission dip stick $100 https://amzn.to/31I2g48 (black) Lokar oil dip stick $100 https://amzn.to/31G0Xm7 you can probably use the factory LS dipsticks, but I always use the lokar...they look nice. depending on year of engine, may need the following single rail fuel rail from 2006+ engine $100 used or buy new billet Truck gas pedal for the DBW (needed for 2003-2007 engine) we have also had good luck just buying a billet block off cap for the return on the fuel rail to save some $ - $75 Custom Exhaust $400-500 Suggested: intake gasket set $60 valve cover gasket set $30 oil pan gasket $30 New power and ground wires to battery $40 You'll also have to figure out some type of cold air intake, i have seen people use the stock truck ones too. I paid like $65 for the chrome one for a silverado on amazon. GAUGES: Depends on what you want to run. You can do custom gauges from Dakota Digital, auto meter, etc, or you can set up stock gauges to work with a convertor from cableX etc. #Pecos #TwoTrucksRon #SquarebodyLSSwap