Скачать с ютуб MERCEDES C200 W203 | REVERSE CAMERA INSTALL GUIDE в хорошем качестве

MERCEDES C200 W203 | REVERSE CAMERA INSTALL GUIDE

DISCLAIMER: A “star” next to the product denotes an affiliate link. If you buy from the affiliate store using this link, I may get a small commission on the sale. Thank you for your continued support This is a comprehensive #DIY video how to install a number plate light-mounted reverse camera on a #Mercedes C200 W203. At the end of this video, I gave this project a #DIYABILITY score so make sure to check that out 👍 🙏 Support my channel: https://www.buymeacoffee.com/autosngi... 🎥 RELATED VIDEOS: 1) Android Headunit Installation Guide:    • MERCEDES C200 W203 | ANDROID HEADUNIT...   2) How to Properly Wire a Reverse Camera:    • HOW TO | CORRECTLY WIRE A REVERSE CAMERA   🔘 PRODUCTS FEATURED IN VIDEO: ⭐️ Android Headunit for MB C200K W203 OPTION 1: 8-inch Screen with built-in wired ACP and AA (https://tidd.ly/3yPeEjz) OPTION 2: 7-inch Screen with built-in wireless ACP and wired AA (https://s.click.aliexpress.com/e/_Af3Hfr) ⭐️ Number Plate Light Reverse Camera for C200K W203 (https://ebay.us/iw8OiI) 🛠 TOOLS OF THE TRADE: ⭐️ SmallRig Professional Phone Video Rig Kit (https://ebay.us/fpnulQ) This is a step up from my old set which was made of poor quality plastic. This kit is more stable and has loads of attachments. I find the power bank holder very useful especially during those extended recording sessions. ⭐️ Engineer Crimping Tool (https://amzn.to/3Rt7H0w) This is a simple yet very effective tool to use for crimping those small JST/Molex connector pins (20-32 AWG Wires). It makes DIY installs look clean and legit. ⭐️ Ratchet & Torx 38-pc Set (https://tidd.ly/3mkoQvI) A good and inexpensive beginner ratchet set. A must have for any automative DIY’er ⭐️ T8-T40 1/4" Torx Security Bit 150mm https://amzn.to/3J80bWr These are long Torx bits useful for reaching those deep/recessed screws ⚙️ HOW TO ENABLE DYNAMIC TRAJECTORY LINES: Go to Settings - Car Infotainment - About Device - Gear/Cog Icon - Passcode (8888) - CAN Type - Change CAN Type to BENZ(Lz) - Save - Reboot NOTE1: You can also search for CAN Type 135 in the text box instead of scrolling through the list WARNING: You might lose your saved Radio stations so you'll have to reprogram your stations all over. ⚙️ HOW TO ENABLE REVERSE CAMERA TRIGGER: Use this setting if your headunit does not automatically show the reverse camera when you put the gear in reverse despite wiring the reverse camera correctly. Go to Settings - Car Infotainment - About Device - Gear/Cog Icon - Passcode (8888) - Backcar setup - Camera Detect (Set to Not Detect) - Save - Reboot WARNING: You might lose your saved Radio stations so you'll have to reprogram your stations all over. 🔘 OTHER CREDITS: Screen resolution comparison website: http://fredfred.net/screen-size-compa... 📖 CHAPTERS 00:00 Introduction 00:37 Prepare the Reverse Camera Wires 03:38 Remove Carpet Trim from Boot Area 10:21 Remove Number Plate Light Cover 10:40 Remove Number Plate Backing Panel 11:52 Remove Number Plate Light Housing 12:56 Wire Management (Melting some plastic) 17:15 Route Wire from Boot to Rear Passenger Compartment 20:57 Connecting to Ground 23:57 Install Number Plate List housing 26:09 Laying Wire from Rear Passenger Compartment to Headunit 36:15 Initial Connectivity Test 38:01 Install Number Plate Backing Panel 39:17 Install Number Plate Light Cover with Reverse Camera 39:57 Screw in Number Plate Backing Panel 40:15 Install Carpet Trim in Boot Area 44:45 Connect Reverse Camera Wire 46:40 Final Connectivity Test 47:01 Close off Headunit 47:21 Real Testing 47:37 DIYABILITY Score 47:54 Affordability (10/10) 49:11 Quality (5/10) 50:35 Satisfaction (8/10) 51:05 Fit and Finish (8/10) 51:28 Fun Factor (8/10) 52:11 Closing